roberto wrote
This looks ODD
scanning ide0: slave
scanning ide1:
Do you have drive hda strapped as a slave?
confirmed see;
> Partition check:
> hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 >
There should not be a hdb, should be hda and hdc
Both drives must be strapped as master or cable-select
Gerald
> With terminal console I got this:
>
> where is the error?
>
>
> Sun Cobalt - Smaller, Bluer, Better, and Free
> Firmware version 2.10.3-ext3
>
> Current date: Jul 09 15:13:51 UTC 2009
> ROM build info: Thu Mar 11 08:51:36 MST 2004 .
> System serial number: Uninitialized
> System type: 3000 series system, Version 2 board
> Silicon serial number: f0000007f5516401
> Monitor: 153536 bytes
> Memory: 384 MB
> CPU: 1 processor(s) detected
> CPU 0: AuthenticAMD 448MHz (4.5 x 100MHz host bus) [BSP]
> Initializing flash: done
> Flash Bank 0: AMD AM29F080B 1024KB (01:d5)
> Flash Bank 1: not installed.
> Mounting ROM fs: done
> Initializing PCI: done
> Host Bus: 0 (device 1f:07) [33MHz]
> Device: 00:00 10b9:1541 Acer Labs M1541 Aladdin V Host Bridge
> Device: 01:00 10b9:5243 Acer Labs M5243 AGP Controller
> Device: 02:00 10b9:5237 Acer Labs M5237 USB Controller (IRQ 6)
> Device: 03:00 10b9:7101 Acer Labs M7101 PMU
> Device: 07:00 10b9:1533 Acer Labs M1543 Aladdin V PCI-ISA Bridge
> Device: 0e:00 1000:000f Symbios Logic SYM53C875 SCSI Controller (IRQ
> 12)
> Device: 0f:00 10b9:5229 Acer Labs M5229 TXpro IDE Controller (IRQ 14)
> Device: 10:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 11)
> Device: 12:00 100b:0020 National DP83815 MacPhyter Ethernet (IRQ 10)
> Bridged Bus: 1 (bridge: 00:01:00)
> Initializing ethernet: 2 controller(s) found
> National Semiconductor DP83815 Found at port 0xfc00, MAC:
> 00:10:e0:04:d1:ff
> National Semiconductor DP83815 Found at port 0xfb00, MAC:
> 00:10:e0:04:d2:02
> Initializing IDE: found ALI M5229 at 00:78
> spinning up second channel: done
> scanning ide0: slave
> scanning ide1:
> IDE: stabilizing spinup: 100%
> Checking Memory: done
>
> Press spacebar to enter ROM mode
> System is in LCD menu mode
> Enabling L2 cache: on-chip L2 is 128K -done
> First stage kernel (Linux): Decompressing - done
> ERROR: cannot relocate with filesize 0
> command line: 'console=ttyS0,115200 debug ip=on root=/dev/nfs
> nfsroot=/nfsroot-x
> 86,rsize=8192 '
> booting kernel...
> Linux version 2.4.25-ROM (duncan (at mark) atherton) (gcc version 3.3.3 (Debian
> 20040306))
> #1 Thu Mar 11 08:47:53 MST 2004
> BIOS-provided physical RAM map:
> BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
> BIOS-e801: 0000000000100000 - 0000000018000000 (usable)
> 384MB LOWMEM available.
> On node 0 totalpages: 98304
> zone(0): 4096 pages.
> zone(1): 94208 pages.
> zone(2): 0 pages.
> DMI not present.
> Kernel command line: console=ttyS0,115200 debug ip=on root=/dev/nfs
> nfsroot=/nfs
> root-x86,rsize=8192
> Initializing CPU#0
> Detected 448.211 MHz processor.
> Calibrating delay loop... 894.56 BogoMIPS
> Memory: 386896k/393216k available (1141k kernel code, 5932k reserved, 244k
> data,
> 100k init, 0k highmem)
> Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
> Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
> Mount cache hash table entries: 512 (order: 0, 4096 bytes)
> Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
> Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
> Enabling new style K6 write allocation for 384 Mb
> CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
> CPU: L2 Cache: 128K (32 bytes/line)
> CPU: After generic, caps: 008021bf c08029bf 00000000 00000002
> CPU: Common caps: 008021bf c08029bf 00000000 00000002
> CPU: AMD-K6(tm)-III Processor stepping 04
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.40 (20010327) Richard Gooch (rgooch (at mark) atnf.csiro.au)
> mtrr: detected mtrr type: AMD K6
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> Starting kswapd
> VFS: Disk quotas vdquot_6.5.1
> Journalled Block Device driver loaded
> pty: 256 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
> SERIAL_PCI en
> abled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> Real Time Clock Driver v1.10f
> Non-volatile memory driver v1.2
> loop: loaded (max 8 devices)
> natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
> originally by Donald Becker <becker (at mark) scyld.com>
> http://www.scyld.com/network/natsemi.html
> 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
> eth0: NatSemi DP8381[56] at 0xd8800000, 00:10:e0:04:d1:ff, IRQ 11.
> eth1: NatSemi DP8381[56] at 0xd8802000, 00:10:e0:04:d2:02, IRQ 10.
> Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> ALI15X3: IDE controller at PCI slot 00:0f.0
> ALI15X3: chipset revision 193
> ALI15X3: 100% native mode on irq 14
> ide0: BM-DMA at 0xfdd0-0xfdd7, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xfdd8-0xfddf, BIOS settings: hdc:DMA, hdd:DMA
> hdb: ST310211A, ATA DISK drive
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> blk: queue c02990dc, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0xfdf8-0xfdff,0xfdf6 on irq 14
> hdb: attached ide-disk driver.
> hdb: 19541088 sectors (10005 MB) w/1024KiB Cache, CHS=19386/16/63,
> UDMA(33)
> Partition check:
> hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 >
> md: linear personality registered as nr 1
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> 8regs : 621.200 MB/sec
> 32regs : 367.200 MB/sec
> pII_mmx : 849.600 MB/sec
> p5_mmx : 825.600 MB/sec
> raid5: using function: pII_mmx (849.600 MB/sec)
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> IP: routing cache hash table of 4096 buckets, 32Kbytes
> TCP: Hash tables configured (established 32768 bind 65536)
> eth0: link up.
> eth0: Setting full-duplex based on negotiated link capability.
> eth1: autonegotiation did not complete in 4000 usec.
> Sending DHCP and RARP requests ., OK
> IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.55
> eth1: remaining active for wake-on-lan
> IP-Config: Complete:
> device=eth0, addr=192.168.1.55, mask=255.255.255.0, gw=192.168.1.1,
> host=192.168.1.55, domain=roberto.ws, nis-domain=(none),
> bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> Looking up port of RPC 100003/2 on 192.168.1.1
> portmap: server 192.168.1.1 not responding, timed out
> Root-NFS: Unable to get nfsd port number from server, using default
> Looking up port of RPC 100005/1 on 192.168.1.1
> portmap: server 192.168.1.1 not responding, timed out
> Root-NFS: Unable to get mountd port number from server, using default
> mount: server 192.168.1.1 not responding, timed out
> Root-NFS: Server returned error -5 while mounting /nfsroot-x86
> VFS: Unable to mount root fs via NFS, trying floppy.
> VFS: Cannot open root device "nfs" or 02:00
> Please append a correct "root=" boot option
> Kernel panic: VFS: Unable to mount root fs on 02:00
>
>